S&S Super Stock Generator Style Crankcases for 1948-'64 Big Twin with Stock Bore - Natural
1936-'69 style oil pump. Machined for 1948-'62 panhead cylinder base oil feed. Machined for 1955-'64 tin primary. Engines for 1936-'64 chassis with tin primary must use a 1954-'64 style inner primary cover. S&S Super Stock generator style crankcases are available for stock 37/16" or 35/8" bore, but can be special ordered for bore sizes up to 313/16" and deck heights as much as 3/16" taller than stock. A special order sheet must be filled out for any special order crankcases. 1936-'54 must use the 1955-'64 style inner steel primary cover. Since all S&S generator style crankcases use 1958 and later style main bearings, stock flywheel assemblies 1957 and earlier cannot be used in S&S crankcases. Flywheel assemblies must have 1958 and later pinion shaft with 1.250" diameter bearing, and a 1954 and later style sprocket shaft designed for a Timken main bearing. Generator style cases for 1936-'47 knucklehead engines are machined to supply oil to the heads from a boss located near the rear tappet guide or from a stock or S&S gearcover. Provision for oil scavenging from the heads in these crankcases is the same as stock, with passageways that connect the tappet guides to the crankcase breather gear. Crankcases for 1948-'69 engines are machined with a provision to separate the oil supply to the top and bottom ends if an S&S oil pump is used. This feature lets you choose the 1972 and earlier stock "side oiling" system or the 1973 and later split oil system. The stock cast iron oil pump can be used for the "original look" and stock oiling system. If an S&S billet oil pump, part #31-6200 is used, the oiling system can be set-up as stock or updated to a split system. 1963-'65 panhead engines, with outside oil supply lines to the cylinder heads, must use the oil supply port located behind the rear tappet guide or the oil fitting toward the rear of the S&S gearcover. S&S generator style crankcases do not have the stock style "outside oiler" oil supply boss, so special oil supply lines will need to be fabricated.
This Super Stock generator style natural finish crankcases is for 1948-'64 big twins with stock bore.
NOTES:1936-'69 style oil pump. Machined for 1948-'62 panhead cylinder base oil feed. Machined for 1955-'64 tin primary. Engines for 1936-'64 chassis with tin primary must use a 1954-'64 style inner primary cover. S&S Super Stock generator style crankcases are available for stock 37/16" or 35/8" bore, but can be special ordered for bore sizes up to 313/16" and deck heights as much as 3/16" taller than stock. A special order sheet must be filled out for any special order crankcases. 1936-'54 must use the 1955-'64 style inner steel primary cover. Since all S&S generator style crankcases use 1958 and later style main bearings, stock flywheel assemblies 1957 and earlier cannot be used in S&S crankcases. Flywheel assemblies must have 1958 and later pinion shaft with 1.250" diameter bearing, and a 1954 and later style sprocket shaft designed for a Timken main bearing. Generator style cases for 1936-'47 knucklehead engines are machined to supply oil to the heads from a boss located near the rear tappet guide or from a stock or S&S gearcover. Provision for oil scavenging from the heads in these crankcases is the same as stock, with passageways that connect the tappet guides to the crankcase breather gear. Crankcases for 1948-'69 engines are machined with a provision to separate the oil supply to the top and bottom ends if an S&S oil pump is used. This feature lets you choose the 1972 and earlier stock "side oiling" system or the 1973 and later split oil system. The stock cast iron oil pump can be used for the "original look" and stock oiling system. If an S&S billet oil pump, part #31-6200 is used, the oiling system can be set-up as stock or updated to a split system. 1963-'65 panhead engines, with outside oil supply lines to the cylinder heads, must use the oil supply port located behind the rear tappet guide or the oil fitting toward the rear of the S&S gearcover. S&S generator style crankcases do not have the stock style "outside oiler" oil supply boss, so special oil supply lines will need to be fabricated.
Instructions Link (Click Here)
Manufacturer: S&S Cycle
Part #: 31-0008
Cross-Reference: The following OEM numbers are provided for reference only and may not be completely accurate.
Harley OEM Cross Reference Numbers:
24519-55
24519-63
S&S Crankcase Assembly 31-0008
- Brand: S&S Cycle
- Product Code: 31-0008
- Availability: Special Order
-
$2,255.95
Tags: S&S Cycle, Harley Davidson, Classic Pre-1984, Engine, Crank Case, Case Sets